Licensed, insured mold remediation done right the first time

Professional Mold Removal in SAN PEDRO, California

Professional Mold Removal in SAN PEDRO, California means finding the moisture source, containing the growth, and removing it to the ANSI/IICRC S520 standard, not just spraying bleach and hoping. We handle attic mold, crawl space mold, bathroom mold recurrence and water damage mold for homeowners and businesses from the San Pedro Waterfront to Vista del Oro. If you can smell it, we can find it.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dependable Mold Remediation Service across SAN PEDRO, California
Careful work. Honest options.
About this service

What Professional Mold Removal in SAN PEDRO, California Actually Involves

Professional Mold Removal in SAN PEDRO, California is a containment-and-removal process that locates the moisture feeding the growth, isolates the affected area with 6-mil plastic sheeting and zipper doors, then physically removes mold from building materials instead of painting over it. We use a moisture meter and thermal imaging camera to trace hidden water, a borescope inspection camera to check inside wall cavities, and an air scrubber with HEPA filter running negative air pressure the whole time so spores do not migrate into clean rooms.

Coastal San Pedro homes sit in a marine layer that keeps relative humidity above 70% for weeks at a time, and that is mold weather. Add a slow supply-line drip behind a vanity in Vista del Oro or a roof leak that soaked attic insulation near Point Fermin, and you have black mold growth within 48 to 72 hours. We see it most in crawl spaces under older Harbor Highlands bungalows, in bathroom ceilings along the Gaffey Street Corridor, and in basements that took on water during winter storms. If you have been searching for expert mold remediation near me SAN PEDRO, that is exactly the call we answer.

  • ✓ Verified Air Quality
  • ✓ Source Fixed, Not Just Scrubbed
  • ✓ Odor Gone, Not Masked
  • ✓ Insurance-Ready Documentation
What's included

What Our Professional Mold Removal Includes

Every remediation job we run includes the full sequence from inspection through clearance testing. Here is what is covered as standard, so you know exactly what you are paying for before we start.

✓

Full Moisture Inspection

We inspect the affected area plus adjacent rooms with a moisture meter and thermal imaging camera, and check inside wall cavities with a borescope inspection camera. This is how we find the water source feeding the mold, which is the step most DIY cleanups skip.

✓

Containment and Air Filtration

We build containment with 6-mil plastic sheeting and zipper doors, then run a negative air machine and air scrubber with HEPA filter for the duration of the job. This keeps mold spores from spreading into clean areas of your home.

✓

Physical Removal and Treatment

Affected drywall, insulation and other porous materials come out. Solid surfaces get HEPA vacuumed, treated with antimicrobial solution, and sealed with a mold encapsulant. For structural surfaces, we may use dry ice blasting machine equipment instead of wet methods.

✓

Drying and Dehumidification

We run a dehumidifier and air mover until framing moisture reads below 16% on the meter. If the space stays damp, mold returns, so we do not skip this step even when the visible growth is already gone.

✓

Post Remediation Clearance Testing

We take air samples after remediation and send them to an independent accredited lab. If spore counts are elevated compared to outdoor baseline, we re-clean at no extra charge. You get the written lab report either way.

✓

Written Report and Repair Scope

You receive photos of every affected area, moisture readings by room, the lab clearance report, and a written scope of any repair work still needed, such as drywall replacement or roof repair. That documentation is formatted for insurance claims.

How it works

Our 5-Step Mold Removal Process

01

Inspection and Testing

A certified mold inspector walks the property with a moisture meter, thermal imaging camera and borescope inspection camera. We take air and surface samples, mark affected zones with tape, and photograph everything. Most inspections take 60 to 90 minutes. You get the lab results and a written scope within 24 to 48 hours.

02

Containment Setup

We seal the work area with 6-mil containment plastic sheeting and zipper doors, then install a negative air machine and air scrubber with HEPA filter. This keeps airborne mold spores from spreading to the rest of your house. Setup usually takes one to two hours depending on how many rooms are involved.

03

Physical Removal

Technicians in personal protective equipment and respirators remove mold-damaged drywall, insulation and framing. Porous materials come out; solid wood gets HEPA vacuumed and treated with antimicrobial solution. For heavy growth on joists and block walls, we use dry ice blasting machine equipment, which strips mold without water or abrasive media.

04

Treatment and Encapsulation

Every exposed surface gets treated with an EPA-registered product such as Concrobium, ShockWave or RMR-86, then sealed with a mold encapsulant. We run a dehumidifier and air mover until framing moisture reads below 16% on the meter. This phase typically takes one to two days.

05

Clearance Testing

We run post remediation mold testing with independent lab analysis before containment comes down. If spore counts are still elevated, we re-clean at no extra charge. Once clearance passes, we hand you the full report, photos and a written scope of any repair work still needed.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture Meter and Thermal Imaging Camera

Used together to trace hidden water behind walls, under flooring and in ceilings without demolition. The thermal camera shows temperature differences that indicate moisture; the meter confirms the reading.

Borescope Inspection Camera

A thin camera that goes through a small drilled hole into wall cavities and ductwork. It lets us see mold growth inside a wall without opening the whole thing up, which saves on repair cost.

Air Scrubber with HEPA Filter

Filters airborne mold spores down to 0.3 microns and runs continuously during remediation. Combined with negative air pressure, it keeps spores from migrating into clean rooms.

Negative Air Machine

Creates negative pressure inside the containment zone so air flows in, not out. This is a core requirement of the ANSI/IICRC S520 standard and one of the main differences between professional and DIY work.

Dry Ice Blasting Machine

Removes mold from framing, block walls and concrete using compressed dry ice pellets. No water, no abrasive media, no secondary residue. Ideal for structural surfaces where moisture is a concern.

HEPA Vacuum and Fogger

The HEPA vacuum removes loose spores from surfaces, and the fogger applies a fine antimicrobial mist into cavities and ductwork. We use EPA-registered products including Benefect and Concrobium.

Dehumidifier and Air Mover

Dries structural materials after water damage or remediation. We run them until framing moisture reads below 16% on the meter, which is the threshold where mold stops growing.

Real results

Before and after.

Bathroom Wall Mold in Vista del Oro

Before

A slow leak behind the shower valve had been running for months. The drywall was black with mold, the caulk line was failing, and the musty odor had spread into the adjacent bedroom. Air sampling showed spore counts three times outdoor baseline.

After

We removed 24 square feet of mold-damaged drywall and insulation, treated and encapsulated the framing, and repaired the valve leak. Post remediation testing came back at outdoor baseline. Total job time was three days from inspection to clearance report.

Crawl Space Mold in Harbor Highlands

Before

A raised-foundation home had visible mold on floor joists and subfloor, with affected insulation falling down in places. The crawl space had no vapor barrier, and relative humidity inside was reading above 85%. The homeowner had been smelling musty odors for two winters.

After

We removed the affected insulation, HEPA vacuumed and treated the joists with antimicrobial solution, and installed a 6-mil vapor barrier across the crawl space floor. Framing moisture dropped below 14% within four days. Air quality testing confirmed spores at outdoor baseline.

Attic Mold After Roof Leak in Point Fermin

Before

A roof penetration had been leaking into the attic for at least one rainy season. Roof sheathing showed black mold growth across roughly 60 square feet, and insulation in that area was saturated. The homeowner noticed a musty smell in the upstairs bedroom.

After

We removed the affected insulation, treated the sheathing and framing with antimicrobial solution, and encapsulated the surfaces. The roofer repaired the penetration, and post remediation testing confirmed clearance. Total remediation time was two days.

Problems we solve

Mold Problems We Solve for San Pedro Properties

These are the calls we get most often in this area. Each one has a specific cause, and each one has a specific fix that goes beyond wiping down the visible growth.

Ask a pro →
01

Black mold growth on bathroom walls and ceilings

We open the affected wall, remove mold-damaged drywall and insulation, treat the framing with antimicrobial solution, and identify the moisture source so you can fix the plumbing. Then we verify clearance with lab testing before closing up.

↗
02

Crawl space mold under raised-foundation homes

We remove affected insulation and debris, HEPA vacuum and treat the joists, then recommend vapor barrier and ventilation improvements. Crawl space mold removal in San Pedro has to account for our coastal humidity, so we size the drying equipment accordingly.

↗
03

Attic mold after a roof leak or poor ventilation

We test the sheathing and insulation, remove affected material, treat the framing, and tell you what roof repair or vent work is needed. Attic mold testing and removal is one of our most common jobs in Point Fermin and South Shores.

↗
04

Water damage mold after a burst pipe or storm

We handle water extraction, structural drying with dehumidifiers and air movers, and mold remediation as one process. That combined approach prevents the mold from returning after the dry-out and gives you one point of accountability.

↗
Proof you can check

Licensed, Certified and Verified

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC Certified Microbial InvestigatorAmerican Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
California Contractors State License Board (CSLB) LicenseCalifornia Contractors State License Board
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential mold jobs in San Pedro run $1,500 to $6,500 as of 2026, with small bathroom or attic spots starting around $850 and full crawl space or basement remediations reaching $10,000 or more. Price depends on square footage affected, material type, and whether containment needs to cover multiple rooms. Testing and clearance add $300 to $700. We give you a fixed written price before any work starts.

Because bleach and store-bought sprays kill surface mold but leave the roots and spores behind, and they do nothing about the moisture feeding it. Expert mold remediation SAN PEDRO crews use HEPA filtration, negative air pressure and lab-verified clearance testing to confirm the problem is actually gone. DIY cleanup on a 20-square-foot patch often spreads spores into adjacent rooms and makes the air quality worse.

We do, and we cover the whole peninsula, from San Pedro Waterfront and Cabrillo Beach up through Miraleste and the Rancho Palos Verdes Border. Call (833) 929-5837 and we will schedule an inspection, usually same day. If you are searching for affordable professional mold removal SAN PEDRO California, ask about our small-job pricing for single-room remediation.

The marine layer. San Pedro sits in coastal humidity that keeps exterior walls and crawl spaces damp for months, so mold here comes back faster than in inland areas if the moisture source is not corrected. We account for that with extended drying times, vapor barrier recommendations in crawl spaces, and dehumidifier placement that matches our local climate rather than a generic playbook.

Ready when you are

Get Professional Mold Removal in SAN PEDRO, California Today

Mold spreads fast in coastal humidity, and every day you wait, the affected area grows. Call (833) 929-5837 for a same-day inspection and a fixed written price. Licensed, insured, and lab-verified clearance on every job.

Schedule Inspection (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837