Lab-backed spore counts for homes and businesses

Mold Spore Testing in SAN PEDRO, California

Mold Spore Testing in SAN PEDRO, California tells you exactly what is floating in your air and whether it is safe to breathe. We run airborne mold spore testing SAN PEDRO homeowners and property managers call for after a roof leak, a burst supply line, or that musty smell in a closed-up room. You get numbers, not guesses, usually within 24 to 48 hours.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Spore Testing by Mold Remediation Service San Pedro
Careful work. Honest options.
About this service

What Mold Spore Testing in SAN PEDRO, California Actually Measures

Mold Spore Testing in SAN PEDRO, California is a diagnostic service that pulls measured volumes of air through a calibrated spore trap, then sends those cassettes to an accredited lab for microscopic identification and counting. You get a raw count per cubic meter, a genus breakdown, and a comparison against an outdoor baseline sample taken the same day. That comparison is the whole point. A spore count means nothing on its own, because outdoor levels in a coastal harbor town swing hard with fog, wind, and construction dust.

We run this test for San Pedro homeowners, landlords, and property managers who suspect hidden growth behind drywall, above ceiling tiles, or under a crawl space vapor barrier. The Pacific Avenue District and Gaffey Street Corridor have a lot of pre-1960 stucco and wood-frame housing stock, and those buildings hide moisture in wall cavities for months before anyone sees a stain. If you have been searching for mold spore sampling near me SAN PEDRO CA, this is the first step before anyone cuts into anything.

  • ✓ Numbers You Can Hand Off
  • ✓ Find Hidden Growth Fast
  • ✓ Know Before You Buy
  • ✓ Confirm the Job Is Done
What's included

What Is Included in Mold Spore Testing

Every job includes the site walkthrough, calibrated air sampling, an outdoor control sample, and the accredited lab report. Here is the full breakdown of what you get, and what we would quote separately if you need it.

✓

Calibrated Air Sampling

We run spore traps at 5 to 10 minutes per location using a calibrated pump. Typical residential jobs use 3 to 5 indoor points plus one outdoor control, with sample volumes logged for the lab.

✓

Moisture and Thermal Survey

A moisture meter and thermal imaging camera map wet areas behind walls and under floors. This is what tells us where to place the air samples so the data actually means something.

✓

Accredited Lab Analysis

Cassettes ship overnight to an accredited third-party lab. You get genus-level identification and counts per cubic meter, with the outdoor control listed side by side for comparison.

✓

Written Report

A PDF report with sample locations, raw counts, genus breakdown, and our interpretation. It is formatted for insurance adjusters, real estate agents, and attorneys who need documentation.

✓

Report Review Call

We walk you through the numbers on the phone, explain what is normal and what is not, and lay out next steps if remediation is needed. No charge for this call and no pressure to book work.

✓

Optional Surface Sampling

Tape-lift or swab samples on visible growth identify the genus directly. We quote these separately, usually $75 to $125 per sample, and only when the air data points to a specific area.

How it works

How Our Spore Sampling Process Works

01

Phone Intake

You describe the smell, the leak, or the visible growth. We ask when it started, whether it is one room or the whole house, and whether anyone has headaches, coughing, or sinus issues. That call takes 10 to 15 minutes and it decides how many sample points you need. Same-day slots are usually open.

02

Walkthrough and Moisture Mapping

On site, we walk the property with a moisture meter and a thermal imaging camera to find temperature differentials behind walls. A borescope inspection camera goes into wall cavities through a 3/8-inch hole where needed. This step takes 30 to 60 minutes and tells us where the air samples should come from.

03

Air and Surface Sampling

We run calibrated spore traps for 5 to 10 minutes per location, indoors and out. Typical jobs use 3 to 5 indoor points plus one outdoor control. Tape-lift or swab samples go on visibly affected surfaces. Every cassette is labeled, logged, and sealed before it leaves the property.

04

Lab Analysis

Samples go to an accredited third-party lab by overnight courier. The lab identifies spores by genus and reports counts per cubic meter. Turnaround is 24 to 48 hours on standard service, with rush options available. You get the raw data, not a summary someone typed up.

05

Report and Action Plan

We walk you through the report line by line. If counts are normal, we tell you that and you are done. If they are elevated, we point to the likely source and lay out what remediation would involve. No pressure, no upsell, and no charge for the review call.

Tools & methods

Tools and Methods We Use for Spore Testing

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Calibrated Spore Trap Pump

Draws a measured volume of air through a cassette at a set flow rate. The exact volume is what lets the lab report counts per cubic meter instead of just a relative number.

Moisture Meter

Reads percent moisture content in drywall, framing, and subfloor. Pin and pinless modes let us check finished surfaces without tearing anything open.

Thermal Imaging Camera

Shows temperature differentials behind walls and above ceilings. Wet material reads cooler, which is how we find hidden moisture before it becomes visible mold.

Borescope Inspection Camera

Goes into wall cavities through a 3/8-inch hole to confirm what the thermal camera suggested. We see the back of the drywall and the framing without a demolition crew.

HEPA Vacuum and Air Scrubber

Used during sampling in affected areas to keep spores from spreading between rooms. HEPA filters capture particles down to 0.3 microns at 99.97 percent efficiency.

Negative Air Machine

Maintains negative pressure in a containment zone so spores do not migrate into clean areas during sampling or remediation work.

Dehumidifier and Air Mover

Dri-Eaz and Phoenix Restoration units pull moisture out of the air and structure. We run them when sampling reveals active moisture that needs to come down fast.

Real results

Before and after.

Hidden Wall Cavity Growth in Barton Hill

Before

A homeowner noticed a musty smell in the master bedroom but no visible mold. A previous contractor had told her it was nothing. Air sampling showed a Penicillium/Aspergillus count of 1,400 spores per cubic meter indoors against an outdoor control of 380.

After

Thermal imaging and a borescope traced the source to a slow supply line leak behind the closet wall. We removed 12 square feet of wet drywall, treated the framing, and ran a HEPA air scrubber. Post-remediation sampling came back at 290 spores per cubic meter, below the outdoor control.

Attic Growth After a Point Fermin Roof Leak

Before

A winter storm pushed water under the flashing on a 1950s bungalow. By the time the owner called us in spring, the attic sheathing had visible dark growth across about 40 square feet. Attic air sampling returned 2,100 spores per cubic meter against an outdoor control of 620.

After

We set containment with plastic sheeting and a negative air machine, removed the affected sheathing, and treated the framing with an antimicrobial solution. The roofer fixed the flashing. Clearance sampling came back at 480 spores per cubic meter, within range of the outdoor control.

Post-Remediation Verification in Harbor Highlands

Before

A landlord had paid a crew to remove bathroom mold in a duplex unit. The tenant still complained about the smell. Baseline sampling from the original job was never done, so there was nothing to compare against. Our first sample showed 1,050 spores per cubic meter in the bathroom.

After

We found the exhaust fan was venting into the attic instead of outside. After rerouting the duct and treating the remaining growth, follow-up sampling came back at 340 spores per cubic meter, below the outdoor control of 410.

Problems we solve

Problems Mold Spore Testing in SAN PEDRO Solves

Most people call us because something is off and they cannot prove it. Testing turns that suspicion into a documented finding you can act on.

Ask a pro →
01

Musty odor with no visible mold

We sample the air in the affected room and compare it to the outdoor control. A genus spike points straight to the source, even when nothing is visible. Then we trace it with a moisture meter and thermal imaging camera.

↗
02

Insurance claim needs documentation

Our reports include raw counts, genus identification, sample locations, and the outdoor baseline. That format is what carriers accept. We have seen claims move from stalled to approved once the lab data landed.

↗
03

Post-remediation doubt

We run clearance testing in the same rooms at the same volumes as the original baseline. If counts do not drop below the outdoor control, we say so in writing and you have grounds to call the contractor back.

↗
04

Real estate transaction uncertainty

A pre-closing spore test gives you a documented baseline. If a reading comes back elevated, you have leverage to negotiate a credit or walk away. It is the cheapest protection in the transaction.

↗
Proof you can check

Credentials and Client Feedback

✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
California Contractors State License Board (CSLB) LicenseCalifornia Contractors State License Board
✓
OSHA 10Occupational Safety and Health Administration
Good questions

Frequently Asked Questions About Mold Spore Testing

(833) 929-5837 →

Most residential jobs run $350 to $750 in 2026, covering 3 to 5 indoor air samples plus one outdoor control and the lab report. Larger homes, commercial spaces, and rush turnaround push the number higher. If you only need one or two rooms checked, we can often keep it under $400. You get the price before we start, and there is no charge for the report review call.

There is no single universal number, because the outdoor control sets the baseline. A normal indoor result is one where total indoor spores are at or below outdoor levels, and no single genus dominates. In San Pedro, outdoor counts often run 500 to 3,000 spores per cubic meter depending on fog and wind. Indoor readings above the outdoor control, or a spike in one water-damage genus like Stachybotrys or Chaetomium, is the flag we look for.

We do, and we cover the whole harbor area, from Cabrillo Beach and Point Fermin up through Barton Hill, Vista del Oro, and the Rancho Palos Verdes border. We also sample commercial buildings near the Port of Los Angeles and Terminal Island. Call (833) 929-5837 and we can usually schedule same-day or next-morning sampling.

Spore trap sampling is accurate enough to be defensible when it is done to the ANSI/IICRC S520 Standard with a calibrated pump and a same-day outdoor control. No air test is 100 percent, because spores settle and shift hour to hour. That is why we take multiple points and pair air data with moisture readings. Used together, the two give you a reliable picture of what is growing and where.

Ready when you are

Book Mold Spore Testing in SAN PEDRO, California Today

One phone call gets a technician to your door, usually the same day. You get accredited lab results in 24 to 48 hours and a straight read on what they mean. Call (833) 929-5837 now and we will get you scheduled.

Schedule Testing Now (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837