Same-day containment, HEPA filtration, and clear post-remediation testing

Mold Cleanup near me in SAN PEDRO, California

When you search for Mold Cleanup near me in SAN PEDRO, California, you want a crew that shows up today, not next week. Our IICRC-certified technicians handle attic, crawl space, and bathroom mold across the Harbor and Gaffey Street Corridor, contain the spores, remove the growth, and verify the air is clean before we pack up. Free estimates, no surprises.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Cleanup Near Me by Mold Remediation Service San Pedro
Careful work. Honest options.
About this service

Mold Cleanup near me in SAN PEDRO, California

Mold Cleanup near me in SAN PEDRO, California is the physical removal of mold growth, contaminated drywall, insulation, and porous materials, followed by HEPA filtration and antimicrobial treatment to stop it from returning. We start with a moisture meter and thermal imaging camera to find the water source, then set up containment plastic sheeting and a negative air machine so spores do not spread to the rest of your home. Growth gets HEPA vacuumed, treated with Fiberlock or Concrobium, and sealed with a mold encapsulant.

San Pedro homes sit close to the water, and that marine layer keeps attics and crawl spaces damp well into spring. We see black mold growth behind bathroom tile in Vista del Oro, musty odors in Harbor Highlands crawl spaces, and ceiling mold after a roof leak near Point Fermin. If you have been searching for mold removal near me SAN PEDRO or an affordable mold cleanup near me SAN PEDRO California, we can usually be on-site the same day you call.

  • ✓ Same-Day Emergency Response
  • ✓ Certified Remediation Crews
  • ✓ Air Testing Before and After
  • ✓ Odor Gone, Not Masked
What's included

What our mold cleanup includes

Every mold cleanup near me in SAN PEDRO job includes the core scope below. Add-ons like dry ice blasting, duct cleaning, or full vapor barrier replacement are quoted separately if needed. You will see the full scope in writing before we start, with a flat price.

✓

Moisture Inspection and Mapping

We use a moisture meter, thermal imaging camera, and borescope inspection camera to find hidden growth and the water source feeding it. You get a written map of affected areas and the source identified before any removal starts.

✓

Containment and Negative Air

The work zone gets sealed with 6-mil containment plastic sheeting and zipper doors. A negative air machine with HEPA filters keeps the space under negative pressure so spores cannot escape into clean rooms.

✓

HEPA Vacuuming and Removal

Contaminated drywall, insulation, and porous materials come out in sealed bags. Framing and hard surfaces get HEPA vacuumed, then treated with an antimicrobial solution like Fiberlock or Concrobium.

✓

Antimicrobial Treatment and Encapsulant

After removal, remaining surfaces get treated and sealed with a mold encapsulant. This locks down any residual spores and gives the surface a moisture-resistant barrier that helps prevent regrowth.

✓

Drying with Dehumidifier and Air Movers

We set a Dri-Eaz dehumidifier and air movers to bring moisture content below 15 percent. Drying typically runs 24 to 72 hours, and we monitor daily until the space reads dry.

✓

Post Remediation Clearance Testing

Air samples go to an accredited lab after the work is done. Results come back in 24 to 48 hours. If counts are still elevated, we re-treat at no extra charge until the space passes.

How it works

What to expect on mold day

01

Phone Triage

We ask where the mold is, how big the area looks, and whether there is an active leak. You get a ballpark range on the call and a two-hour arrival window. If it is an emergency, we roll a crew immediately, including nights and weekends.

02

On-Site Inspection

A certified inspector walks the space with a moisture meter, thermal imaging camera, and borescope inspection camera. We map the moisture, find the source, and check the attic, crawl space, and HVAC returns. Most inspections take 45 to 60 minutes and you get findings the same visit.

03

Containment and Removal

We seal the work zone with 6-mil containment plastic sheeting and zipper doors, then run a negative air machine with HEPA filters so spores cannot drift into clean rooms. Contaminated drywall and insulation come out in sealed bags. A HEPA vacuum and antimicrobial solution follow.

04

Treatment and Drying

Remaining framing gets treated with Fiberlock or Concrobium and sealed with a mold encapsulant. We set a Dri-Eaz dehumidifier and air movers to bring moisture content below 15 percent. Drying typically runs 24 to 72 hours depending on how wet the structure is.

05

Clearance Testing

Once drying is complete, we take post-remediation air samples and send them to an accredited lab. Results come back in 24 to 48 hours. If counts are still elevated, we re-treat. If they are clear, you get a written report you can hand to your insurer, buyer, or landlord.

Tools & methods

Tools and standards we use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Moisture meter and thermal imaging camera

Find hidden moisture behind walls and ceilings before we open anything up. Thermal imaging shows temperature differences that point to wet materials.

Borescope inspection camera

Lets us look inside wall cavities and crawl spaces without cutting large access holes. We confirm growth and moisture before quoting the removal.

Air scrubber with HEPA filter and negative air machine

Keeps the work zone under negative pressure and filters airborne spores down to 0.3 microns. Essential for keeping the rest of the home clean.

Dri-Eaz dehumidifier and air movers

Pull moisture out of framing and drywall after removal. We monitor daily until moisture content drops below 15 percent.

HEPA vacuum and fogger

HEPA vacuuming removes settled spores from surfaces. The fogger applies antimicrobial treatment into cavities and porous materials that wiping cannot reach.

Dry ice blasting machine

Removes mold from framing and block walls without water or abrasive media. Ideal for attics and structural lumber where added moisture is a problem.

Fiberlock, Concrobium, RMR-86, Benefect, ShockWave

Antimicrobial treatments and encapsulants we use after removal. Each is chosen based on the surface and the species identified in testing.

Real results

Before and after.

Bathroom mold behind vanity

Before

A slow supply line leak in a Vista del Oro bathroom had been running for weeks. Black mold growth covered the back of the vanity cabinet and the drywall behind it. Moisture meter read 28 percent in the affected wall.

After

We removed the vanity, cut out the affected drywall, HEPA vacuumed and treated the framing, and ran a dehumidifier for 48 hours. Post-remediation air samples came back at outdoor levels. Total job took three days.

Attic mold after roof leak

Before

A roof leak near Point Fermin soaked attic insulation and sheathing over one winter. Visible black mold covered roughly 60 square feet of sheathing, and the smell was noticeable from the hallway below.

After

We removed wet insulation under containment, HEPA vacuumed and treated the sheathing and rafters, and installed new insulation. Moisture content dropped from 24 percent to 11 percent. Clearance testing passed on the first round.

Crawl space mold and vapor barrier failure

Before

A Harbor Highlands home had a torn vapor barrier and standing moisture in the crawl space. Floor joists showed surface mold, and the house smelled musty year-round. Relative humidity in the crawl space read 78 percent.

After

We removed debris, HEPA vacuumed and treated the joists with antimicrobial, installed a new 10-mil vapor barrier, and set a dehumidifier. Humidity dropped to 52 percent within a week. The musty smell was gone.

Problems we solve

Mold problems we fix across the Harbor

Most of the calls we get are one of these five problems. Each one has a specific fix, and each one gets worse if you wait.

Ask a pro →
01

Black mold growth behind bathroom walls

We locate the leak with a moisture meter and borescope, remove affected drywall and tile backer, treat the framing with antimicrobial solution, and rebuild the wall after clearance testing confirms the space is clean.

↗
02

Musty odors that keep coming back

We trace the odor with a thermal imaging camera and borescope, find the moisture source, and treat the space with a fogger and ShockWave or Benefect. Air scrubbers run until the smell is gone, not masked.

↗
03

Attic mold from poor ventilation

We remove contaminated sheathing and insulation under containment, HEPA vacuum the framing, treat with antimicrobial, and often recommend added ventilation to prevent recurrence.

↗
04

Crawl space mold and standing moisture

We remove debris and growth, HEPA vacuum and treat the joists, install a new vapor barrier, and set a dehumidifier to keep the space dry long term.

↗
Proof you can check

Licensed, certified, and documented

✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
OSHA 10Occupational Safety and Health Administration
✓
CSLB Licensed California ContractorCalifornia Contractors State License Board
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs in SAN PEDRO run $450 to $2,800 in 2026, with the average single-room bathroom or closet job landing around $1,100. Attic and crawl space jobs with extensive growth typically run $2,000 to $6,500 because of access and disposal. Emergency calls, containment size, and whether drywall or insulation has to come out are the biggest cost drivers. We give you a flat written price before we start.

Our IICRC-certified crew handles mold removal near me in SAN PEDRO, from initial inspection through clearance testing. We are a CSLB-licensed California contractor based in the Harbor area, so we know the local housing stock. Call (833) 929-5837 and you will talk to a technician, not a call center. Same-day inspections are usually available.

Yes. We run 24/7 mold cleanup near me SAN PEDRO CA dispatch for active leaks, sewage backups, and post-storm intrusion. A crew can usually be on-site within two hours. Emergency response focuses on stopping the water source, setting containment, and starting extraction so mold does not have time to colonize. Full remediation follows once the space is dry.

Most jobs start the same day you call, and nearly all within 24 hours. If you reach us before noon, we can usually inspect and begin containment by late afternoon. Larger attic or crawl space jobs may be scheduled for the next morning so we can bring the right equipment. We confirm the start time on the phone and text you when the crew is en route.

Ready when you are

Need Mold Cleanup near me in SAN PEDRO, California today?

Call (833) 929-5837 and talk to a certified technician, not a call center. Free estimates, flat pricing, and same-day dispatch for active leaks. We answer 24/7 and can usually be on-site within two hours anywhere in the Harbor area.

Get Free Estimate (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837