Containment, removal and clearance testing for homes and businesses

Mold Abatement in SAN PEDRO, California Done Right

Mold Abatement in SAN PEDRO, California means stopping active growth, pulling contaminated material, and proving the air is clean before we pack up. We handle attic, crawl space and bathroom mold across the harbor area, from Cabrillo Beach to the Gaffey Street Corridor. If you smell that musty odor or see black mold growth, call (833) 929-5837 and we will scope it the same day.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Mold Remediation Service San Pedro — your local Mold Remediation Service team
Careful work. Honest options.
About this service

What Mold Abatement in SAN PEDRO, California Covers

Mold Abatement in SAN PEDRO, California is the physical removal of mold colonies, contaminated drywall, insulation and framing, followed by treatment and clearance verification. It is not a bleach wipe-down. We build containment with plastic sheeting and zipper doors, run a negative air machine with HEPA filters, and keep airborne mold spores from spreading into the rest of your house while we work. Every job follows the ANSI/IICRC S520 Standard for Mold Remediation.

Harbor-area homes get hit from three directions: marine humidity off the Port of Los Angeles, roof and window leaks during winter storms, and plumbing failures behind old bathroom walls. We see crawl space mold under raised foundations in Vista del Oro and attic mold along the Palos Verdes Drive East corridor after a wet January. If you have been searching for mold mitigation near me SAN PEDRO, that search usually starts with a smell you cannot find and a stain you keep painting over.

  • ✓ Air You Can Breathe
  • ✓ Musty Odor Gone
  • ✓ Structural Damage Stopped
  • ✓ Documented for Insurance
What's included

What Our Mold Abatement Includes

Every abatement quote covers the full path from inspection to clearance. We do not split containment, removal and testing into separate invoices to make the headline number look smaller. Here is what is in the scope, and what we price separately only when it applies to your job.

✓

Moisture Inspection and Mapping

A certified mold inspector documents wet zones with a moisture meter, thermal imaging camera and borescope inspection camera. You get a written scope with square footage, material counts and photographs before any containment goes up.

✓

Containment and Negative Air

We build 6-mil containment with zipper doors and run a negative air machine with HEPA filters for the duration of the job. That keeps airborne mold spores out of the rest of your home while we work.

✓

Removal and HEPA Vacuuming

Contaminated drywall, insulation and trim come out in sealed bags. Framing and hard surfaces get HEPA vacuuming, then a full antimicrobial wipe-down. Heavy growth on wood gets dry ice blasting instead of wet cleaning.

✓

Treatment and Encapsulation

We apply an antimicrobial solution followed by a mold encapsulant on porous framing. Products include Fiberlock, Concrobium, RMR-86 and Benefect. Wide-area coverage gets a fogging pass with a ShockWave or similar fogger.

✓

Post Remediation Clearance Testing

An independent spore sampling pass compares indoor counts against an outdoor baseline. We do not remove containment until the numbers clear. If a room fails, we re-clean at no additional charge.

✓

Written Documentation Package

Photographs, moisture readings, material quantities, product data sheets and the final lab report, assembled the way insurance adjusters expect. That package protects you at claim time and at resale.

How it works

How Our Mold Abatement Process Works

01

Inspection and Mapping

A certified mold inspector walks the property with a moisture meter, thermal imaging camera and borescope inspection camera. We map every wet zone, photograph readings, and identify the water source. Expect 45 to 90 minutes for a typical single-family home. You get a written scope with square footage and material counts before any work starts.

02

Containment Build

We seal the work area with 6-mil containment plastic sheeting, duct tape and zipper doors, then install a negative air machine so the room stays under pressure. That pressure difference is what keeps spores from drifting into your kitchen. Setup takes two to four hours on a standard bedroom or bathroom job.

03

Removal and HEPA Vacuuming

Contaminated drywall, insulation and trim come out and go into sealed bags. Framing and hard surfaces get HEPA vacuuming with ProTeam and 3M units, then a full wipe-down. On heavy growth we switch to dry ice blasting, which lifts mold off wood without soaking it further.

04

Treatment and Encapsulation

We apply an antimicrobial solution, then a mold encapsulant on porous framing to seal what remains. Products we use include Fiberlock, Concrobium, RMR-86 and Benefect. For wide-area coverage we fog with a ShockWave or similar fogger. This step typically takes one full day.

05

Clearance Testing

An independent post remediation mold testing pass compares indoor spore counts against an outdoor baseline. We do not remove containment until the numbers clear. If a room fails, we re-clean at no additional charge. Most SAN PEDRO jobs pass on the first clearance.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Reveals temperature differences behind walls and under flooring, which is how we find hidden moisture without opening every surface. It is the fastest way to locate a leak you cannot see.

Moisture Meter

Confirms wet readings in drywall, framing and subfloor. We log every reading so you have a documented baseline and a way to verify the structure is dry before we close it up.

Borescope Inspection Camera

Slips through a small drilled hole to show what is growing inside a wall cavity. It saves you from exploratory demolition when a targeted look is enough.

Air Scrubber with HEPA Filter

Continuously filters airborne mold spores inside containment. We size the unit to the cubic footage of the work zone so the air exchanges per hour meet the ANSI/IICRC S520 Standard.

Negative Air Machine

Keeps the work zone under negative pressure so spores travel into the HEPA filter, not into your living room. It runs from containment build to final clearance.

Dry Ice Blasting Machine

Lifts mold off framing and masonry without water or abrasive media. It is our preferred method on attic rafters and crawl space joists where wet cleaning would feed the problem.

HEPA Vacuum and Dehumidifier

HEPA vacuuming removes settled spores from hard surfaces. Dri-Eaz and Phoenix Restoration dehumidifiers pull moisture out of framing before and after abatement so growth does not restart.

Real results

Before and after.

Attic Mold After a Roof Leak

Before

A homeowner in Point Fermin noticed a stain on the ceiling and a musty smell in the hallway. A roof leak had been feeding the attic decking for months. Thermal imaging showed wet sheathing across three bays, with visible black mold growth on the rafters.

After

We removed 240 square feet of contaminated sheathing and insulation, dry ice blasted the rafters, and applied encapsulant. Clearance testing came back at 180 spores per cubic meter indoors against a 420 outdoor baseline. Job completed in four days.

Bathroom Mold Recurrence Stopped

Before

A Vista del Oro homeowner had cleaned bathroom mold four winters in a row. The growth kept returning along the ceiling and the back wall of the shower. A moisture meter showed the wall cavity was wet, and the exhaust fan was venting into the attic instead of outside.

After

We removed the colonized drywall and insulation, treated the framing with an antimicrobial solution, and reinstalled moisture-resistant board. The exhaust fan was re-ducted to the exterior. Clearance passed on the first test. Job took three days.

Crawl Space Mold Under a Raised Foundation

Before

A Barton Hill home had a persistent musty odor in the living room. The crawl space had visible mold across the floor joists and subfloor, with standing moisture after winter rains. Insulation was saturated and hanging loose in several bays.

After

Our crew removed 320 square feet of contaminated insulation, HEPA vacuumed and treated the joists, and dry ice blasted heavy growth off the subfloor. A vapor barrier was installed. Clearance numbers dropped from 1,100 spores per cubic meter to 210. Job completed in five days.

Problems we solve

Mold Problems We Solve in SAN PEDRO

Most mold calls start the same way: a smell, a stain, or a leak you thought you fixed. Here are the four problems we see most often in harbor-area homes and how we handle each one.

Ask a pro →
01

Musty odor with no visible growth

We use thermal imaging and a borescope inspection camera to find the moisture source, then sample the air to confirm what is growing. Once located, we open the cavity, remove contaminated material, and treat the framing with an antimicrobial solution before closing it back up.

↗
02

Bathroom mold that keeps coming back

We remove the colonized drywall and insulation, treat the substrate, and identify the moisture path. If the exhaust fan is undersized or ducted wrong, we tell you what to fix. That is the difference between abatement and a cleanup that fails in three months.

↗
03

Attic mold after a roof or vent leak

We remove contaminated sheathing and insulation, dry ice blast the rafters to lift mold without adding water, then apply encapsulant. Ventilation corrections get quoted separately so you can decide whether to fix the cause now or later.

↗
04

Crawl space mold under a raised foundation

Our crawl space mold removal crews suit up in full PPE, run negative air, and remove colonized material. We treat the framing, then recommend a vapor barrier or ventilation fix so the same joists do not re-colonize next winter.

↗
Proof you can check

Licensed, Certified, Documented

✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC Certified Microbial InvestigatorAmerican Council for Accredited Certification
✓
California Contractors State License Board (CSLB) RegistrationState of California
✓
OSHA 10 CertificationOccupational Safety and Health Administration
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs in SAN PEDRO run $1,200 to $6,500 in 2026, with small bathroom or ceiling mold abatement starting around $850 and whole-attic or crawl space jobs reaching $9,000 or more. Square footage of affected material, containment complexity, and whether we are opening walls drive the number. We give you a fixed written price after the inspection.

Abatement is the physical removal of mold and contaminated material. Mitigation is the broader plan: fixing the moisture source, drying the structure, and preventing recurrence. In practice, mold mitigation SAN PEDRO jobs include abatement plus moisture control. Skipping the mitigation half is why bathroom mold recurrence happens three months after a cheap cleanup.

We do. Our crews cover every SAN PEDRO neighborhood, from the San Pedro Waterfront and Downtown San Pedro to White Point, Royal Palms and the Rancho Palos Verdes Border. Call (833) 929-5837 and we will schedule an inspection, usually same day. We handle residential, commercial and emergency calls.

A single bathroom or closet typically takes two to three days. A full attic, crawl space or multi-room job runs four to seven days. The clock includes containment setup, removal, treatment, and clearance testing. Drying time after a water leak can add one to two days before abatement can start.

Ready when you are

Get Mold Abatement in SAN PEDRO, California Today

If you see black mold growth, smell something musty, or just had a leak, do not wait for it to spread. We inspect, scope and quote the same day, with a fixed price before any work starts. Call (833) 929-5837 now.

Book an Inspection (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837