Chemical-free mold removal for homes and businesses on the harbor

Dry Ice Blasting Mold in SAN PEDRO, California

Dry Ice Blasting Mold in SAN PEDRO, California is the fastest way to strip mold off wood, brick, and framing without water, sand, or harsh chemicals. If you own a 1920s bungalow near the Gaffey Street Corridor or a harbor-front commercial building, our team removes growth, kills spores, and leaves the surface dry and ready to seal. Call (833) 929-5837 for same-day dry ice mold removal SAN PEDRO.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service San Pedro
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in SAN PEDRO, California Does

Dry Ice Blasting Mold in SAN PEDRO, California is a media blasting method that fires rice-sized dry ice pellets at 300 to 500 mph to lift mold, mildew, and surface grime off structural surfaces. The pellets hit at -109 degrees Fahrenheit, flash-freeze the mold, and sublimate straight from solid to gas. That means no water, no sand cleanup, and no chemical residue left behind in your walls, attic, or crawl space.

In SAN PEDRO, the combination of marine humidity, older housing stock, and winter roof leaks creates perfect mold conditions. We see black mold growth behind bathroom tile in Vista del Oro, attic mold along rafters in Barton Hill, and crawl space mold under 1940s homes near Pacific Avenue District. If you have been searching for dry ice mold removal near me SAN PEDRO, our crew handles the full job from inspection through final clearance testing.

  • ✓ No Water, No Secondary Damage
  • ✓ Reaches Tight Spaces
  • ✓ Kills Spores at the Source
  • ✓ Safe for Wiring and Plumbing
What's included

What Our Dry Ice Blasting Mold Service Includes

Every job includes the full scope from inspection through clearance testing. We do not piece out the work or leave you to coordinate between contractors. Here is what you get when you hire us for dry ice blasting mold in SAN PEDRO California.

✓

Full Mold Inspection

We use a moisture meter, thermal imaging camera, and borescope inspection camera to map every affected area. You get photos and moisture readings documented before we start.

✓

Containment and Air Filtration

We seal the work zone with containment plastic sheeting and zipper doors, then run a negative air machine and air scrubber with HEPA filter. This keeps spores out of your clean living space.

✓

Dry Ice Blasting

Our technician blasts every contaminated surface with a dry ice blasting machine. Pellets hit at 300 to 500 mph and lift mold off wood, brick, and concrete without water or chemicals.

✓

HEPA Vacuum and Antimicrobial Treatment

We HEPA vacuum all surfaces, then apply an antimicrobial solution like Concrobium or Benefect. Severe cases get a mold encapsulant or ShockWave to seal porous materials.

✓

Third-Party Clearance Testing

An independent lab runs post remediation mold testing to confirm spore counts are back to normal. You get the written report for your records, insurance, or landlord.

✓

Debris Disposal

We bag and dispose of all mold-contaminated debris according to California Department of Public Health guidelines. You do not touch anything.

How it works

Our Dry Ice Mold Removal Process

01

Inspection and Testing

We arrive within 60 minutes for emergencies and start with a moisture meter and thermal imaging camera to map the extent of the problem. Air samples go to a third-party lab, and you get results in 24 to 48 hours. Our ACAC Certified Microbial Investigator documents every affected area before we touch anything.

02

Containment Setup

We seal off the work zone with containment plastic sheeting and zipper doors, then install a negative air machine and air scrubber with HEPA filter. This keeps mold spores from spreading to clean rooms while we work. Setup takes about 45 minutes on a standard residential job.

03

Dry Ice Blasting

Our technician suits up in personal protective equipment and respirators, then runs the dry ice blasting machine across every contaminated surface. Pellets hit at 300 to 500 mph and lift mold off wood, brick, and concrete. A 500-square-foot attic takes 4 to 6 hours to blast clean.

04

HEPA Vacuum and Treatment

After blasting, we HEPA vacuum every surface to capture loose debris, then apply an antimicrobial solution like Concrobium or Benefect. For severe cases we follow with a mold encapsulant or ShockWave to seal porous materials. A fogger handles any remaining airborne spores in hard-to-reach voids.

05

Clearance Testing

We run post remediation mold testing with a third-party lab to confirm spore counts are back to normal outdoor levels. If anything is still elevated, we re-clean at no extra charge. You get the lab report in writing, which most SAN PEDRO landlords and insurers require before closing out a claim.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires rice-sized dry ice pellets at 300 to 500 mph to lift mold off wood, brick, and concrete without water or chemicals.

Thermal Imaging Camera

Detects temperature differences behind walls to find hidden moisture and mold growth without tearing into finished surfaces.

Borescope Inspection Camera

Slides through a 1-inch access hole to inspect inside wall cavities and ductwork for mold growth you cannot see.

Air Scrubber with HEPA Filter

Filters airborne mold spores down to 0.3 microns, keeping the air clean during and after blasting.

Negative Air Machine

Creates negative pressure in the containment zone so spores cannot escape into clean areas of your home.

HEPA Vacuum

Captures loose mold debris and spores from surfaces after blasting. We use ProTeam and 3M units.

Moisture Meter

Measures moisture content in drywall, wood, and concrete to find the water source feeding the mold.

Real results

Before and after.

Bathroom Mold Removal in Vista del Oro

Before

A slow leak behind the shower wall fed black mold growth for months. The homeowner noticed a musty odor and discoloration on the drywall. Air samples showed spore counts 4 times higher than outdoor levels.

After

We contained the bathroom, blasted the mold off the framing with dry ice, HEPA vacuumed the debris, and treated with antimicrobial solution. Post remediation mold testing confirmed spore counts back to normal in 48 hours.

Attic Mold Remediation in Barton Hill

Before

A roof leak went unnoticed for two winters, spreading mold across 400 square feet of rafters and roof decking. The attic smelled musty and insulation was contaminated.

After

We set up containment, blasted the mold off rafters and decking, HEPA vacuumed the insulation, and applied mold encapsulant to seal the wood. The attic passed clearance testing on the first try.

Crawl Space Mold Removal in Downtown San Pedro

Before

A 1940s bungalow near Pacific Avenue District had crawl space mold across floor joists and subfloor. Ground moisture and no vapor barrier created constant humidity. The homeowner noticed sagging floors.

After

We blasted the mold off joists and subfloor, treated with antimicrobial solution, and installed a 6-mil vapor barrier. Moisture readings dropped from 22 percent to 11 percent within a week.

Problems we solve

Mold Problems We Solve in SAN PEDRO

SAN PEDRO's marine climate and older housing stock create specific mold problems. Here are the ones we see most often and how we fix them.

Ask a pro →
01

Black mold growth behind bathroom walls

We find the leak with a moisture meter and thermal imaging camera, blast the mold off the framing with dry ice, treat with antimicrobial, and repair the moisture source so it does not come back.

↗
02

Attic mold along rafters and roof decking

We contain the attic, blast mold off rafters and decking, HEPA vacuum the insulation, and treat with mold encapsulant. We also recommend ventilation upgrades to prevent recurrence.

↗
03

Crawl space mold under raised foundations

We blast mold off joists and subfloor, treat with antimicrobial, and install a vapor barrier if needed. We also check drainage and recommend fixes to keep the space dry.

↗
04

Musty odors that keep coming back

We track the odor to its source with a borescope inspection camera, blast the hidden mold, and run a fogger with antimicrobial solution to kill remaining spores in voids.

↗
Proof you can check

Licensed, Certified, and Insured

✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
OSHA 10Occupational Safety and Health Administration
✓
ACAC Certified Microbial InvestigatorAmerican Council for Accredited Certification
Good questions

Frequently Asked Questions About Dry Ice Blasting Mold

(833) 929-5837 →

Most residential jobs run $1,200 to $4,500 in 2026, depending on square footage and how far the mold has spread. A single bathroom or small attic averages $1,200 to $2,000. Whole-house remediation with crawl space and attic work runs $3,500 to $8,000. We give you a written price before we start, and we bill insurance directly when coverage applies.

It is a cleaning method that fires dry ice pellets at 300 to 500 mph to lift mold off wood, brick, and concrete. The pellets hit at -109 degrees Fahrenheit, freeze the mold, and sublimate into gas. No water, no sand, no chemical residue. We follow with HEPA vacuuming, antimicrobial treatment, and third-party clearance testing to confirm the mold is gone.

Our team at Mold Remediation Service San Pedro handles dry ice blasting mold removal across SAN PEDRO and the surrounding harbor area, including Terminal Island, San Pedro Waterfront, and the Palos Verdes Drive East corridor. Call (833) 929-5837 and we can usually be on-site within 60 minutes for emergencies. We are licensed, insured, and IICRC certified.

Yes. Dry ice blasting is non-toxic, non-conductive, and safe for wiring, plumbing, and most building materials. We use containment plastic sheeting, negative air machines, and HEPA filters to keep spores out of clean areas. Our crews wear personal protective equipment and respirators, and we follow the ANSI/IICRC S520 Standard for Mold Remediation on every job.

Ready when you are

Get Dry Ice Blasting Mold in SAN PEDRO, California Today

Mold spreads fast in SAN PEDRO's marine climate. Every day you wait, the colony grows and the job gets more expensive. Call (833) 929-5837 now for a same-day inspection and a written price. Licensed, insured, and IICRC certified.

Call Now (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837