Licensed crews dry, treat, and seal your crawl space for good

Crawl Space Mold Removal in SAN PEDRO, California

Crawl Space Mold Removal in SAN PEDRO, California is what we do every day, from Point Fermin bungalows to White Point hillside homes. If you smell that wet-cardboard musty odor or your floors feel soft, mold is already feeding on the joists underneath. We inspect with moisture meters and thermal cameras, contain the growth, and remove it to ANSI/IICRC S520 standards so the spores stop cycling into your living space.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Local Mold Remediation Service team in SAN PEDRO
Careful work. Honest options.
About this service

Crawl Space Mold Removal in SAN PEDRO, California

Crawl Space Mold Removal in SAN PEDRO, California means physically removing mold growth from joists, subfloor, insulation, and ductwork, not painting over it. We set containment plastic sheeting and zipper doors, run a negative air machine with HEPA filters, then HEPA vacuum every surface before applying an antimicrobial solution and mold encapsulant. Wood that reads above 20 percent moisture on a meter gets dried first with air movers and a dehumidifier, because mold returns in weeks if the water source stays active.

San Pedro sits on the harbor with marine air pushing humidity into older pier-and-beam homes all year. Add a slow supply-line drip or a winter storm that backs water under the house, and you have ideal conditions for black mold growth and airborne mold spores. Homeowners call us most often after a musty odor shows up in a hallway closet, or after a home inspector flags crawl space mold during a sale. If you have been searching crawl space mold remediation near me SAN PEDRO, we handle the whole job, inspection to clearance testing.

  • ✓ Healthier Indoor Air
  • ✓ Protects Structural Wood
  • ✓ Kills the Musty Odor
  • ✓ Higher Resale Value
What's included

What Our Crawl Space Mold Removal Includes

Every crawl space mold treatment SAN PEDRO job we run includes the full sequence from inspection through clearance. We do not sell piecemeal work, because partial remediation is how mold comes back. Here is what is standard on every job, and what we only add when the crawl space actually needs it.

✓

Full Crawl Space Inspection

Moisture meter readings at every joist, thermal imaging of the subfloor, and borescope inspection of tight bays. We photograph everything and map the growth on a floor plan so you can see exactly where the problem sits.

✓

Containment and Negative Air

6-mil containment plastic sheeting, zipper doors at the access hatch, and a negative air machine with HEPA filters. This keeps spores from migrating into your living space during removal. Setup and teardown are included in the quoted price.

✓

Physical Mold Removal

HEPA vacuuming of all surfaces, removal of mold-damaged insulation and drywall, and dry ice blasting or wire brushing of framing. We remove growth, we do not seal it in place. Debris is bagged and disposed of properly.

✓

Antimicrobial Treatment and Encapsulation

Application of an antimicrobial solution followed by a mold encapsulant on all cleaned framing. We use Fiberlock and RMR-86 products, and we fog with Benefect or Concrobium to reach areas a sprayer cannot.

✓

Drying to Below 16 Percent

Air movers and a Dri-Eaz dehumidifier run until framing moisture content drops below 16 percent. This step usually takes 24 to 72 hours, and we monitor with a moisture meter until the numbers hold.

✓

Post-Remediation Clearance Testing

Independent air sampling compared against an outdoor baseline, with a written clearance report. If the numbers do not pass, we re-treat at no additional cost. This is the documentation your lender, buyer, or insurance adjuster wants to see.

How it works

How Our Crawl Space Mold Removal Process Works

01

Inspection and Testing

A certified mold inspector walks the crawl space with a moisture meter, thermal imaging camera, and borescope inspection camera. We map the growth, find the water source, and take air and surface samples. You get lab results and a written scope, usually within 24 hours.

02

Containment Setup

We seal the access hatch and build containment with 6-mil plastic sheeting and zipper doors. A negative air machine with HEPA filters pulls the space under negative pressure so spores cannot drift into your kitchen while we work. Setup takes about an hour on a typical job.

03

Removal and Cleaning

Technicians in full personal protective equipment and respirators HEPA vacuum every surface, then remove mold-damaged insulation and drywall. Stubborn growth on joists comes off with dry ice blasting or wire brushing, followed by an antimicrobial solution. This stage runs two to six hours depending on square footage.

04

Drying and Treatment

We position air movers and a Dri-Eaz dehumidifier to bring framing below 16 percent moisture content, which usually takes 24 to 72 hours. Then we fog the space with Concrobium or ShockWave and apply a mold encapsulant to lock down any residual spores.

05

Clearance Testing

Once everything is dry and treated, we run post-remediation mold testing with independent air samples. If spore counts come back at or below outdoor baseline, the job passes. You receive the clearance report, plus photos of the before and after, for your records or your lender.

Tools & methods

Tools and Methods We Use Under Your House

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Thermal Imaging Camera

Reveals temperature differences that point to hidden moisture behind subfloor sheathing and inside joist bays, so we find growth that a visual inspection would miss.

Borescope Inspection Camera

Slides into tight bays and behind ductwork to confirm growth and capture photos. Essential on older San Pedro homes with limited crawl space access.

Negative Air Machine with HEPA Filters

Pulls the crawl space under negative pressure during removal so airborne mold spores cannot drift up into your living areas through floor gaps.

Dry Ice Blasting Machine

Removes mold from rough-sawn framing without water or abrasive media. Our preferred method on historic redwood joists where we want to preserve the original wood surface.

Dri-Eaz Dehumidifier and Air Movers

Bring framing moisture content below 16 percent after removal. We monitor with a moisture meter until the readings hold for 24 hours.

HEPA Vacuum and Fogger

HEPA vacuuming captures settled spores on every surface, and the fogger applies Benefect or Concrobium into joist bays and corners a sprayer cannot reach.

Real results

Before and after.

Waterfront Bungalow With Black Mold on Joists

Before

A 1945 bungalow near the San Pedro Waterfront had a slow drain leak wetting the same joist bay for over a year. Black mold growth covered roughly 120 square feet of framing, insulation was saturated, and the musty odor reached the bedrooms.

After

We removed the damaged insulation, dry ice blasted the joists, and dried the framing from 28 percent moisture content down to 12 percent over three days. Clearance testing came back at outdoor baseline. The odor was gone within 24 hours.

Escrow Rescue in Vista del Oro

Before

A buyer's inspector flagged crawl space mold nine days before closing on a 1958 Vista del Oro home. Roughly 60 square feet of surface growth on subfloor sheathing, plus mold on flex duct insulation. The lender required documented remediation before funding.

After

We inspected Wednesday, remediated Thursday and Friday, and had clearance results back Monday. Spore counts dropped from 4,200 spores per cubic meter to 380, below the outdoor baseline of 520. Escrow closed on schedule.

Storm Flooding Under a Barton Hill Home

Before

A winter storm pushed two inches of standing water under a Barton Hill pier-and-beam home. It sat for six days before the homeowner called. Insulation was soaked, and visible mold had started on the lower six inches of every joist in the affected area.

After

We extracted the water, set air movers and a Dri-Eaz dehumidifier, and dried the framing from 32 percent to 13 percent moisture content in 72 hours. Antimicrobial treatment and encapsulation followed, and the space passed clearance on the first test.

Problems we solve

Crawl Space Problems We Solve in San Pedro

Most crawl space calls come down to four root causes. Fix the cause and the mold stops coming back. Treat the mold alone and you will be calling someone again next winter.

Ask a pro →
01

Persistent musty odor through the house

We locate the growth with a borescope inspection camera, remove it, and treat the space with a fogger. Most San Pedro homeowners notice the odor is gone within 24 hours of the final treatment, and it does not come back once the water source is fixed.

↗
02

Soft or bouncy floors over the crawl space

We dry the framing below 16 percent moisture content, remove the mold, and encapsulate the wood. If any joist has lost too much section, we flag it for a licensed carpenter and coordinate the repair so the floor is solid again.

↗
03

Mold flagged during a home inspection

We move fast on escrow timelines. Inspection within 24 hours, remediation scheduled around your closing date, and clearance testing with a written report you can hand straight to the buyer or lender. Most jobs clear within five business days.

↗
04

Recurring mold after a previous spray treatment

We strip the growth physically with dry ice blasting or HEPA vacuuming, dry the wood, then encapsulate. That is the ANSI/IICRC S520 sequence, and it is why our jobs pass clearance testing the first time.

↗
Proof you can check

Licensed, Certified, and Documented

✓
IICRC WRT (Water Restoration Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
IICRC AMRT (Applied Microbial Remediation Technician)Institute of Inspection, Cleaning and Restoration Certification
✓
ACAC Certified Microbial InvestigatorAmerican Council for Accredited Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
California Contractors State License Board (CSLB) licenseState of California
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $1,800 to $6,500 in 2026, with the average San Pedro home landing around $3,200. Small, contained growth on a few joists can come in under $2,000. Larger jobs with damaged insulation, ductwork, or widespread framing growth push higher. Square footage, access difficulty, and whether the water source needs repair all move the number.

Marine humidity off the harbor keeps crawl space wood above 15 percent moisture much of the year, and that is all mold needs. Add a slow plumbing drip, poor drainage, or a foundation vent blocked by landscaping, and growth starts in days. Older pier-and-beam homes near the water are the most common calls we get.

We do, and we are local to the Harbor Area. Our crews work out of San Pedro and cover Point Fermin, Vista del Oro, Harbor Highlands, and the Rancho Palos Verdes Border. Call (833) 929-5837 and we can usually inspect the same day or next morning, with lab results back within 24 to 48 hours.

It depends on the cause. Sudden events like a burst pipe or appliance failure are often covered under standard homeowner policies. Long-term seepage and gradual humidity damage usually are not. We document everything with photos, moisture readings, and a written scope, which is exactly what adjusters ask for when you file a claim.

Ready when you are

Get Crawl Space Mold Removal in SAN PEDRO, California Today

If you smell musty air or your inspector flagged growth under the house, call (833) 929-5837. We answer 24/7, inspect fast, and give you a fixed written price before any work starts. Licensed, insured, and lab-verified at clearance.

Book Free Inspection (833) 929-5837 →
Request an appointment

Contact Our San Pedro Mold Crew

Call us at (833) 929-5837 any time, day or night. We answer live 24/7 for emergencies and schedule same-day inspections for non-urgent jobs. You can also email info@moldremediationservicesanpedro.com and we will respond within a few hours during business hours.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837